By Eric Andrew Kristof, RN, CAHIMS | Healthcare IT Professional | HIMSS Arkansas Chapter Member
About This Series: The HIMSS Word of The Day is a running blog series drawing from the HIMSS Dictionary of Health Information and Technology Terms, Acronyms, and Organizations, 6th Edition (2025) — the authoritative reference for healthcare IT professionals and the primary study resource for CAHIMS and CPHIMS certification. Each post paraphrases the term in plain language, grounds it in real-world healthcare IT context, and adds a bedside nursing perspective you won’t find in a textbook.
📖 The Term: Traceroute
Source: HIMSS Dictionary of Health Information and Technology Terms, Acronyms, and Organizations, 6th Edition (2025)
🔍 Plain-Language Definition
The HIMSS Dictionary describes traceroute as a network diagnostic tool that tracks the route a packet takes across an IP network from source to destination, recording how long each hop takes. It says the tool relies on ICMP echo packets that carry changing Time To Live (TTL) values.
That last detail is only partly right across tools. Microsoft’s documentation for the Windows tracert command says it sends ICMP echo requests, or ICMPv6 for IPv6, with a TTL that starts at 1 and rises by 1 with each probe. The Linux traceroute man page says something different about its defaults: probes are UDP datagrams sent to high-numbered, normally unused ports, with ICMP echo probes and TCP SYN probes available as options. The Cisco troubleshooting note read for this post also describes UDP probes sent to an invalid port. The man page documents traceroute 2.1.6 and carries a 2006 date, so a given system may behave differently.
The mechanism is the same in each case. Each router that forwards a packet reduces its TTL, and when the value reaches zero the router discards the packet and may send back an ICMP Time Exceeded message. RFC 792, published in September 1981, describes this message as ICMP type 11, with code 0 for TTL expiry in transit, and says it returns the original datagram’s IP header plus the first 64 bits of its data. The source address of that reply identifies the router, so a probe with TTL 1 reveals the first hop, TTL 2 the second, and so on.
| Item | Detail |
|---|---|
| What it does | Reveals routers along a path and time for each hop |
| Core mechanism | Probes with rising TTL values and ICMP Time Exceeded replies |
| Windows command | tracert, using ICMP echo requests |
| Linux default | UDP probes, with ICMP and TCP options |
| Default hop limit | 30 for both the Windows tool and the Linux man page |
| Typical output | Hop number, three round-trip times, and router address or name |
⚠️ Exam Alert: Traceroute shows the path and per-hop delay, while ping tests whether a destination answers. A traceroute asterisk means no reply was received for that probe in the time allowed, not proof that the router is down. Questions may say traceroute uses ICMP echo, which matches Windows but not every implementation.
🌐 Why It Matters: Real-World Healthcare IT Context
There is no health care research specific to this tool, so this section relies on standards and vendor documentation. The statements below describe how the tools are documented, not how any hospital network behaves.
Reading the output. Microsoft’s page says each output line shows the hop number, three round-trip times in milliseconds, and the router’s address or name, which is usually the near-side interface closest to the sending device. Names appear when reverse lookup succeeds, and the /d option turns off name resolution, which can speed results. The default maximum is 30 hops, adjustable with the /h option.
What asterisks mean. Microsoft’s page says a row of asterisks means that the router did not send a Time Exceeded reply, so it is hidden from the trace. The Linux man page says an asterisk means no reply arrived for that probe before the timeout. The Cisco note says an asterisk means the probe timed out and also describes other letters that mark specific ICMP error replies, such as one for a destination administratively prohibited by an access list. Because the cause of an asterisk is not explained by the tool, one asterisk does not tell the reader whether a hop is failing or simply not replying.
Limits of the numbers. The Cisco note says replies to ping and traceroute come from a router’s processing path, so a busy router may answer slowly, and it says round-trip times from these tools are too imprecise for performance evaluation. A high number at one hop does not prove that hop is the problem, particularly if later hops show normal times.
Probe types. The Linux man page describes a TCP SYN option, with port 80 as the default, that uses a half-open technique intended to get past firewalls that block UDP or ICMP. When a network blocks one probe type, a different type may produce a different picture, which is why a trace should be read as one view of the path and not the whole truth.
Why it matters in health care. Network and application teams may run a trace when a clinical application or device cannot reach its server, to see where along the path replies stop or slow. The tool does not identify the cause, and results from a workstation reflect that workstation’s path at that moment.
Common traceroute problems:
- Reading an asterisk as proof that a router is down
- Treating one slow hop as the cause when later hops are normal
- Assuming every system sends ICMP echo probes
- Comparing round-trip times as if they were precise measurements
- Sharing full traces without considering that they reveal internal network addresses
What supports using traceroute:
- A simple path view that uses a mechanism described in RFC 792
- Built-in availability on common operating systems
- Options that let a user change probe type or hop limit
- A repeatable first step when a connection fails, to be followed by deeper checks
🏥 The Nurse’s Perspective: Clinical, Bedside, & Workflow
Nurses rarely run traceroute, but they are often the first to notice and report the symptoms that lead a network team to run one.
At the Bedside
A mobile cart that cannot reach the EHR, a medication scanner that stops syncing, or a monitor that drops off the central station are the kinds of events that prompt a network check. Noting the time, the location, and what was on screen helps, because a path problem may be brief or limited to one area.
In Clinical Workflow
Nurse informaticists often relay these reports to network and application teams, and they can ask whether a path check was done and whether the problem is local or wider. Knowing that a trace shows one workstation’s route at one moment helps set expectations about what the result can prove.
In EHR Implementation (Go-Live Perspective)
During an Epic Go-Live, analysts at the elbow hear reports of slowness or disconnects that turn out to depend on location. Recording the device, the unit, the time, and the exact message gives the network team what it needs. This post does not claim that any specific go-live involved a traceroute.
🎓 CAHIMS / CPHIMS & HIMSS Perspective
CAHIMS Exam Domain Mapping
Traceroute supports infrastructure and troubleshooting knowledge:
| CAHIMS Domain | How Traceroute Appears |
|---|---|
| Healthcare & Technology Environments | Networks, protocols, and diagnostic tools |
| Clinical Informatics | Understanding why a clinical application is slow or unreachable |
| Healthcare Information & Systems Management | Troubleshooting steps and escalation to network teams |
| Management & Leadership | Setting expectations about what diagnostic tools can prove |
Key Terms to Know Alongside Traceroute
- ICMP — the Internet Control Message Protocol, used for error and diagnostic messages
- TTL (Time To Live) — a value that limits how many hops a packet can take
- Hop — one router step along a packet’s path
- Packet — a unit of data sent across an IP network
- WAN — a wide area network that links sites across distances
- Ping — a tool that tests whether a destination answers
HIMSS Organizational Position
HIMSS offers education and research on health information and technology topics through its Resource Center. Members can find related information on the HIMSS Resource Center page.
🔗 Explore Further: External References
- Linux man-pages — traceroute(8) https://man7.org/linux/man-pages/man8/traceroute.8.html
- Microsoft Learn — tracert https://learn.microsoft.com/en-us/windows-server/administration/windows-commands/tracert
- IETF — RFC 792, Internet Control Message Protocol (September 1981) https://www.rfc-editor.org/info/rfc792/
- Cisco — Understanding the Ping and Traceroute Commands https://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-software-releases-121-mainline/12778-ping-traceroute.html
- HIMSS — Resource Center https://www.himss.org/resource-center
Term source: HIMSS Dictionary of Health Information and Technology Terms, Acronyms, and Organizations, 6th Edition (2025). All definitions in this series are paraphrased for editorial purposes. Readers are encouraged to consult the primary source for exact language.
Eric Andrew Kristof, RN, CAHIMS is a Healthcare IT professional and HIMSS Arkansas Chapter member based in Hot Springs Village, AR, with hands-on Epic Go-Live experience and a diverse healthcare and IT background. He writes at kristof.org at the intersection of clinical care and healthcare technology.

Leave a Reply